A properly installed Asphalt Driveway in San Jose, CA, can last 20 to 30 years with regular maintenance. The lifespan of an Asphalt Driveway depends a lot on how well the subgrade preparation is done, the Asphalt Mix Design that is used, and the compaction achieved during the installation. Things like heavy vehicle traffic and constant direct sunlight without Sealcoating can make an Asphalt Driveway wear out faster. That is why we recommend Sealcoating every two to three years. This protects the Asphalt Driveway surface from UV damage and moisture intrusion. Charis Paving Co focuses on building a solid foundation and a dense Asphalt Mat to make sure your Asphalt Driveway lasts a long time. Charis Paving Co provides Asphalt Driveway services for homes in San Jose, CA.

The way Charis Paving Co handles residential driveway Asphalt Paving in San Jose starts with getting the ground ready. We begin by digging out the old surface and then we grade the subgrade. This makes sure that water will drain away correctly from your new driveway. Next, Charis Paving Co puts in a strong foundation. We install a minimum of 6 to 8 inches of Class 2 aggregate base rock. This Class 2 aggregate base rock is crushed material that is good for making a solid, compactable foundation for driveways in San Jose. We compact this base rock to make a very stable base. After the base rock is in place, we apply a tack coat. This tack coat is an asphalt emulsion. The tack coat helps the new asphalt layer stick to the base rock underneath. This is important so the layers bond together and act as one unit. Finally, we lay down 2 to 3 inches of hot mix asphalt. Our team compacts this asphalt with vibratory rollers. This compaction makes sure the asphalt has good density and a smooth finish. This whole process results in a durable and even Asphalt Paving surface for your San Jose home. Charis Paving Co provides Asphalt Paving services for homes in San Jose, CA.

Proper Drainage is very important for Asphalt surfaces in San Jose, CA. Standing water causes a lot of problems for Asphalt Pavement. When water gets down into the aggregate base of the Asphalt, it can make the foundation weak. This weakness can lead to Potholes, Cracking, and the whole Asphalt Pavement breaking down. This is especially true during the winter rainy season in San Jose, CA. Charis Paving Co always designs the slopes and grades of your Asphalt Paving to make sure water flows away from the paved area. We will often put in catch basins or swales to help with this. This stops hydrostatic pressure from building up under the Asphalt Pavement. This means your Asphalt will stay stable and intact for a longer time in San Jose, CA. Charis Paving Co provides Asphalt Paving services for homes and businesses in San Jose, CA.

An Asphalt Driveway in San Jose needs regular maintenance. This maintenance primarily consists of Asphalt Sealcoating and Asphalt Crack Filling. Asphalt Sealcoating should be applied every 2 to 3 years. This protects the asphalt from oxidation. Oxidation is caused by the sun's UV rays. Sealcoating also protects against water penetration. This preserves the binder and the aggregate in the Asphalt Driveway. Cracks in the Asphalt Driveway, especially those wider than a quarter-inch, should be filled promptly. We use hot-applied Crack Sealant for this. This stops water from reaching and eroding the sub-base beneath the Asphalt Driveway. Neglecting these steps allows water to get in. Water infiltration leads to more extensive and costly Asphalt Driveway repairs later on. Charis Paving Co provides Asphalt Sealcoating and Asphalt Crack Filling services for homes in San Jose, California.

Charis Paving Co makes sure Asphalt Installation is done right with a careful multi-step process. This process focuses on the right materials and good compaction. We only use Caltrans-approved hot mix asphalt for Asphalt Installation projects in San Jose. We pick the right size of aggregate and the correct binder content for the traffic that the new asphalt will see. Our crews follow strict compaction rules for all Asphalt Installation work. We use heavy vibratory rollers to get at least 92% density, which is very important for how long the asphalt will last and how it handles heavy loads. We also do density testing to check the compaction levels. This is because if the compaction is not good enough, the asphalt will wear out too fast and get ruts. This way of working, from the subgrade to the final rolling, makes sure the Asphalt Installation in San Jose is solid and will last a long time.